Castrol GPS

GUIDE TO INDUSTRIAL PRODUCTS AND SERVICES

Issue link: http://read.dmtmag.com/i/814629

Contents of this Issue

Navigation

Page 375 of 385

1 800 255 4417 www.castrol.com/GPS March 2017 Glossary of Terms EP Additives – Per AGMA, these are now known as Anti-Scuffing additives. Reduce friction, wear, and scoring under certain conditions of boundary lubrication. Chemical EP additives are more or less corrosive depending on type and actual conditions of service. Lubricating solids, Tribol Gear Oil Additive (TGOA) and Micro Flux Trans (MFT) can provide EP characteristics without corrosive chemical action in a non-sacrificial manner. EP Lubricants – Lubricants that have been fortified with additives that appreciably increase the load carrying properties of the base lubricant, as defined by AGMA or other agency, thus reducing excessive wear. These additives may be based on liquid or soluble chemistries, solids or combinations, thereof. F Falex Wear & EP Test – Determines the extreme pressure (EP) and anti-wear properties of oil or grease. Clamped between two Vee blocks, a standard Test Pin is rotated while load is applied. Falex wear is done by subjecting a lubricant to a constant test load (ex: 350 or 700 lbs. Force) for 15 minutes. The number of teeth advanced on the standard loading gear (ratchet wheel) in order to maintain the test load is a measure of the wear. Note: It has been found that 1 tooth advanced is equivalent to 0.000056 inch of wear. Falex EP test is done by subjecting a lubricant to increasing load until failure occurs as indicated by high torque/temperature, seizure and/or breakage of the test pin or shear pin. Film Strength – The property of an oil (sometimes defined as cohesiveness, i.e. the oil film's ability to remain as continuous) which enables it to maintain an unbroken film on lubricated components during operations. Rupture of the film could result in be scuffing or scoring of the surfaces. Filter – Any device, media or porous material used to remove particulate matter from fluids. Filters may be inline with other components such as pumps and circulation equipment or "kidney lube" design. Fire Point – Continuation of the Flash Point test which measures the lowest temperature at which a fluid gives off sufficient vapors to burn for at least 5 seconds when a small flame is passed over the surface of the sample. Flash Point (COC) (Cleveland Open Cup Test) – This ASTM D-92 test determines the lowest temperature at which a fluid gives off sufficient vapors to ignite, but not continue burning, when a small flame is passed over the surface of the sample. Flash Point (PMCC) (Pensky-Martens Closed Cup Tester) – A method of test, ASTM D-93, for the determination of the flash point of liquid fuels or solvents flashing below 175°F, with the exception of fuel oils. Flash Point Test (Tag Closed-Cup Tester) – A method of test, ASTM D-56, for the determination of the flash point of liquid fuels or solvents flashing below 175° F, with the exception of fuel oils. Foam – A froth produced by mechanical action that introduces air into a lubricant. Four-Ball EP Test – This test is made with four steel balls arranged in the form of Equilateral Tetrahedron (pyramid). The result determines the EP characteristics of lubricants by means of a load scar measured in mm and a weld point measured in kgf. Evaluates wear preventive properties under much higher unit loads than the FOUR BALL WEAR TEST. Four-Ball Wear Test – Determines the wear preventive properties under conditions of boundary lubrication. Carried out under specific speed, temperature and load conditions with four balls arranged in the form of a Equilateral Tetrahedron (pyramid). Results are measured in mm, the average diameter of the scars on the lower three balls in the pyramid. Fretting – The removal of extremely fine particles by the action of adhesive forces between bearing surfaces. Occurs when bearings are subjected to slight but continued vibration. Often called fretting corrosion or false brinelling. S4

Articles in this issue

Links on this page

view archives of Castrol GPS - GUIDE TO INDUSTRIAL PRODUCTS AND SERVICES