Castrol GPS

GUIDE TO INDUSTRIAL PRODUCTS AND SERVICES

Issue link: http://read.dmtmag.com/i/814629

Contents of this Issue

Navigation

Page 133 of 385

Hydraulic, Turbine and Circulating Fluids 1 800 255 4417 www.castrol.com/GPS March 2017 Industrial Lubricants Product Data Fire-Resistant Hydraulic Fluids Fire-resistant fluids are used in any hydraulic application where a significant fire risk has been identified should the fluid be released from the primary system. These fluids are not fire-proof, but have properties that increase their resistance to fire in comparison to mineral oils. Many types of fire-resistant fluids are available, but the two most common ones are synthetic polyol esters (Castrol Anvol SWX series) and water glycol (Castrol Anvol WG 46). Polyol esters are fully synthetic fluids that contain no water. They offer greater fire resistance than mineral oils through higher flash and fire points along with lower heat of combustion. They are often compatible with mineral oils, making changeover much simpler than with other fire-resistant fluid types. In addition, polyol esters typically provide similar lubrication properties and have similar seal compatibility to mineral oils. On the downside, they do not offer the same level of fire resistance as water glycols since they contain no water. Water glycol fluids are a combination of water (typically 35-40%), diethylene glycol and additives to improve wear protection and corrosion resistance. A vapor-phase corrosion inhibitor is also included to protect the vapor spaces of hydraulic systems above the fluid line. Water glycols offer a high degree of fire resistance due to the water content, but are less effective as lubricants when compared to mineral oils and polyol esters. For this reason, water glycols typically have limited pressure ranges and hydraulic component manufacturers often de-rate their components when running water glycol. Additionally, due to the greatly differing chemistries, changeover from mineral or other oil to water glycol requires a thorough flush and review of system elastomers for compatibility. Long-Term Oxidation Resistance Polyol esters can vary greatly in their performance in hydraulic systems, especially when it comes to oxidation resistance. Many fluids on the market start off with good performance but often reach a point where they begin to show a sharp spike in oxidation, leading to fluid degradation and varnish. This is due to use of lower quality base oils and insufficient additives. Castrol formulated Anvol SWX to overcome this problem and provide end users with long drain intervals. Left: Leading competitor polyol ester (ISO 68) after test. Note from 3rd party lab: "Failed – turned to glue" Right: Castrol Anvol SWX 68 after test. Oil remains clear and fluid. TOST Oxidation Test (ASTM D 943) Leading competitor polyol ester. Sludge coating entire hydraulic system due to poor oxidation resistance. Note (not Revisions Product Name ISO VGs Available Base Oil Additives 1 Viscosity Index Zinc Flash Point Range 3 Pour Point Range 3 Oxidation Resistance 2 Pressure Range Rev 5 includes Hydraulic & Circulating Oils Rev 6 - Moved Hyspin VG 32 - 220 Mineral R&O 95 No 410 - 469°F -22 to +14°F üü n/a Rev 6 - Changed Hyspin AWS 15 - 150 Mineral AW > 95 Yes 383 - 450°F -27 to +5°F ü 5000+ psi Rev 6 - Moved Hyspin ZZ 32 - 68 Mineral AW > 95 No 410 - 439°F -17 to -11°F üü 5000+ psi Hyspin AWH-M 15, 32-150 Mineral AW / VII > 130-150 Yes 401 - 450°F -60 to -22°F ü 5000+ psi Hyspin HVI 15, 32, 46 Mineral AW / VII > 150 No 320 - 428°F -54 to -33°F üü 5000+ psi Tribol HM 943 22 - 100 Mineral AW > 100 No 374 - 486°F -34 to -11°F üüü 7500+ psi Spindle Oils Hyspin Spindle Oil 2, 10 22 Mineral R&O 86-100 No 176°F (2) 295°F (10) 414°F (22) -40 to -22°F üü n/a Hyspin Spindle Oil HS 2 Mineral AW n/a Yes 200°F n/a üü n/a Turbine Oils Perfecto X 32 - 68 Mineral R&O 112 No 432 - 453°F +5 to +10°F üüü n/a Perfecto XEP 46 Mineral AW 112 No 453°F +5°F üüü n/a Environmentally Responsible Performance Bio HE PBL 32 - 46 Plant-based AW 206 - 217 Yes 460 - 580°F n/a ü < 5000 psi Performance Bio HE ESU 46 Synthetic Ester AW 185 No 518°F -17°F üüü 7500+ psi Fire-Resistant Hydraulic Fluids Anvol SWX 46, 68 Polyol Ester AW 180 No > 536°F -33 to -27°F üüü 7500+ psi Anvol WG 46 Water Glycol AW > 200 No n/a -60°F n/a < 3000 psi Specialty Circulating Fluids Magna CTX WT (steel mill circulating oil) 460, 680 Mineral AW 92 - 97 No 469 - 475°F +16 to +21°F üü n/a Tribol CT 1740 (paper machine oil) 220, 320 Semi-Synthetic AW 145 No 510°F -13 to -3°F üüü n/a Food Grade Hydraulic Oil Optileb HY 32, 46, 68 Synthetic PAO AW 136 - 143 No 426 - 468°F -58 to -49°F üüü 7500+ psi Hydraulic Oils 1 R&O = Rust & Oxidation inhibitors AW = Anti-wear VII = VI improver 2 Increasing performance from 1 to 3 checks 3 Varies by viscosity grade Note (not Revisions Product Name ISO VGs Available Base Oil Additives 1 Viscosity Index Zinc Flash Point Range 3 Pour Point Range 3 Oxidation Resistance 2 Pressure Range Rev 5 includes Hydraulic & Circulating Oils Rev 6 - Moved Hyspin VG 32 - 220 Mineral R&O 95 No 410 - 469°F -22 to +14°F üü n/a Rev 6 - Changed Hyspin AWS 15 - 150 Mineral AW > 95 Yes 383 - 450°F -27 to +5°F ü 5000+ psi Rev 6 - Moved Hyspin ZZ 32 - 68 Mineral AW > 95 No 410 - 439°F -17 to -11°F üü 5000+ psi Hyspin AWH-M 15, 32-150 Mineral AW / VII > 130-150 Yes 401 - 450°F -60 to -22°F ü 5000+ psi Hyspin HVI 15, 32, 46 Mineral AW / VII > 150 No 320 - 428°F -54 to -33°F üü 5000+ psi Tribol HM 943 22 - 100 Mineral AW > 100 No 374 - 486°F -34 to -11°F üüü 7500+ psi Spindle Oils Hyspin Spindle Oil 2, 10 22 Mineral R&O 86-100 No 176°F (2) 295°F (10) 414°F (22) -40 to -22°F üü n/a Hyspin Spindle Oil HS 2 Mineral AW n/a Yes 200°F n/a üü n/a Turbine Oils Perfecto X 32 - 68 Mineral R&O 112 No 432 - 453°F +5 to +10°F üüü n/a Perfecto XEP 46 Mineral AW 112 No 453°F +5°F üüü n/a Environmentally Responsible Performance Bio HE PBL 32 - 46 Plant-based AW 206 - 217 Yes 460 - 580°F n/a ü < 5000 psi Performance Bio HE ESU 46 Synthetic Ester AW 185 No 518°F -17°F üüü 7500+ psi Fire-Resistant Hydraulic Fluids Anvol SWX 46, 68 Polyol Ester AW 180 No > 536°F -33 to -27°F üüü 7500+ psi Anvol WG 46 Water Glycol AW > 200 No n/a -60°F n/a < 3000 psi Specialty Circulating Fluids Magna CTX WT (steel mill circulating oil) 460, 680 Mineral AW 92 - 97 No 469 - 475°F +16 to +21°F üü n/a Tribol CT 1740 (paper machine oil) 220, 320 Semi-Synthetic AW 145 No 510°F -13 to -3°F üüü n/a Food Grade Hydraulic Oil Optileb HY 32, 46, 68 Synthetic PAO AW 136 - 143 No 426 - 468°F -58 to -49°F üüü 7500+ psi Hydraulic Oils 1 R&O = Rust & Oxidation inhibitors AW = Anti-wear VII = VI improver 2 Increasing performance from 1 to 3 checks 3 Varies by viscosity grade Note (not Revisions Product Name ISO VGs Available Base Oil Additives 1 Viscosity Index Zinc Flash Point Range 3 Pour Point Range 3 Oxidation Resistance 2 Pressure Range Rev 5 includes Hydraulic & Circulating Oils Rev 6 - Moved Hyspin VG 32 - 220 Mineral R&O 95 No 410 - 469°F -22 to +14°F üü n/a Rev 6 - Changed Hyspin AWS 15 - 150 Mineral AW > 95 Yes 383 - 450°F -27 to +5°F ü 5000+ psi Rev 6 - Moved Hyspin ZZ 32 - 68 Mineral AW > 95 No 410 - 439°F -17 to -11°F üü 5000+ psi Hyspin AWH-M 15, 32-150 Mineral AW / VII > 130-150 Yes 401 - 450°F -60 to -22°F ü 5000+ psi Hyspin HVI 15, 32, 46 Mineral AW / VII > 150 No 320 - 428°F -54 to -33°F üü 5000+ psi Tribol HM 943 22 - 100 Mineral AW > 100 No 374 - 486°F -34 to -11°F üüü 7500+ psi Spindle Oils Hyspin Spindle Oil 2, 10 22 Mineral R&O 86-100 No 176°F (2) 295°F (10) 414°F (22) -40 to -22°F üü n/a Hyspin Spindle Oil HS 2 Mineral AW n/a Yes 200°F n/a üü n/a Turbine Oils Perfecto X 32 - 68 Mineral R&O 112 No 432 - 453°F +5 to +10°F üüü n/a Perfecto XEP 46 Mineral AW 112 No 453°F +5°F üüü n/a Environmentally Responsible Performance Bio HE PBL 32 - 46 Plant-based AW 206 - 217 Yes 460 - 580°F n/a ü < 5000 psi Performance Bio HE ESU 46 Synthetic Ester AW 185 No 518°F -17°F üüü 7500+ psi Fire-Resistant Hydraulic Fluids Anvol SWX 46, 68 Polyol Ester AW 180 No > 536°F -33 to -27°F üüü 7500+ psi Anvol WG 46 Water Glycol AW > 200 No n/a -60°F n/a < 3000 psi Specialty Circulating Fluids Magna CTX WT (steel mill circulating oil) 460, 680 Mineral AW 92 - 97 No 469 - 475°F +16 to +21°F üü n/a Tribol CT 1740 (paper machine oil) 220, 320 Semi-Synthetic AW 145 No 510°F -13 to -3°F üüü n/a Food Grade Hydraulic Oil Optileb HY 32, 46, 68 Synthetic PAO AW 136 - 143 No 426 - 468°F -58 to -49°F üüü 7500+ psi Hydraulic Oils 1 R&O = Rust & Oxidation inhibitors AW = Anti-wear VII = VI improver 2 Increasing performance from 1 to 3 checks 3 Varies by viscosity grade H 13

Articles in this issue

Links on this page

view archives of Castrol GPS - GUIDE TO INDUSTRIAL PRODUCTS AND SERVICES