Landscape and Irrigation is read by decision makers throughout the landscape and irrigation markets — including contractors, landscape architects, professional grounds managers, and irrigation and water mgmt companies and reaches the entire spetrum.
Issue link: http://read.dmtmag.com/i/96774
Gicon Pumps RWHC Rainwater Harvesting Controller Gicon Pumps and Equipment introduced the RWHC Rainwater Harvesting Control System, which interfaces irrigation controls, tank level controls and pump operation into one simple-to-install system. The RWHC control system comes in 7 models, 6 for pump operation for horsepower ranges from 2 through 10 horsepower, voltages from 230 single phase to 460 three phase, and a controls-only version for installation with existing pump starters or pump systems. The system features: * Nema 3R enclosure for outdoor installation. * U.L. Listed. * Main circuit breaker disconnect with through-the-door operator. * IEC contactors. * IEC overloads on all three phase models. * Control power transformer with primary and secondary fuses. * Pump run light indicator. * Low water level shutdown indicator light. * Alternate fill source light indicator. * Internal switch for automatic remote fill source operation. * Terminal strip for easy interface to irrigation controls, floats and pump. * Float switches for full automatic operation. Hunter Node battery-operated controller For isolated sites and power-restricted areas, the Hunter Node is the smart, reliable solution. The Node mounts to a valve's solenoid quickly and easily, and without screws, drills or additional wires. The unit's solid construction and waterproof exterior ensure it can handle the harsh environment of a valve box. The Node is powered by one or two 9V batteries, and provides standard or extended power throughout the season. Along with exceptional reliability, the Node features an easy-to-program LCD screen, the ability to control a Master Valve, and uses standard Hunter controller programming with 3 programs and 4 start times per program. The array of programming options and rugged reliability make the Node a compact and powerful irrigation controller with the flexibility of battery power. Irrisoft Weather Reach Controller Link Controller Link uses WiFi or wired ethernet to retrieve hourly weather conditions, calculating plant water use based on data from high-quality sensor measurements of solar radiation, wind, humidity, temperature and rain. Housed in a weather-tight enclosure, Controller Link is a simple, quick and effective retrofit to existing sprinkler timers. Controller Link combines site-specific settings with real-time ET and rainfall measurements to manage watering on up to four programs. Program Start Sensors detect the beginning of a watering cycle, then Controller Link interrupts or enables the valve common. Deep, less frequent watering improves plant health and reduces water waste. Controller Link uses the Ideal Irrigation Amount, which is based on soil type and root depth to know how deep to water. Watering frequency is determined based on "Managed Allowed Depletion." An advanced real-time moisture balance uses hourly ET and on-site rain measurements to control irrigation. If available watering days are limited because of watering restrictions or facility use, the Look-Ahead feature estimates the next watering event and may allow watering the day before an "off" day. An effective rain algorithm interrupts watering when it rains and knows how long to wait to resume watering once the storm is over. Irritrol R-100 programmable remote To make irrigation troubleshooting and maintenance easier and faster, Irritrol introduced a new remote, the R-100. Besides immediate savings in time and money, the remote ships with advanced technology for future products and programming. Using the remote, an irrigation professional, working alone, can walk the green space activating and shutting off sprinkler zones as needed. The remote has "future-needs" technology built into it for increased control, productivity and savings down the line. A built-in USB port, for a computer connection, and the open architecture of the microprocessor allow for yet-to-be developed features, firmware updates, and even working with future products using the same handheld remote. And future upgrades are coming, including being able to control a landscape lighting system. The Irritrol Remote Kit includes the remote, a mini-receiver, and an RJ-11 cable. The remote works by connecting the mini-receiver to the irrigation system controller. (The remote is compatible with over 50 controller models.) Commands sent from the remote will then operate the controller while the contractor is in the field. The range of the remote is approximately 1,000 feet (line-of-sight). One remote can control different systems with PIN codes, allowing one contractor to administer many irrigation systems. The Remote KIT has a list price of $165. Many contractors increase their system sales by selling a remote to the end user. The handheld remote lists by itself (if the irrigation system already has Climate Logic) for $99.50. www.landscapeirrigation.com Landscape and Irrigation 21