IDA Universal

May/June 2017

Issue link: https://read.dmtmag.com/i/820377

Contents of this Issue

Navigation

Page 29 of 55

I DA U N I V E R S A L M ay -J u n e 2 0 1 7 30 GPS GPS machine control started out as a tangle of aftermarket products all bolted on and wired up as retrofi ts to existing dozers. These systems revolu- tionized the operation of dozers, but there were a lot of parts to track and maintain. In the past 18 months, however, several major manufac- turers have begun integrating these systems into the physical structure of their machines, creating integrated systems that not only improve the grade control perfor- mance, but make the process less cumbersome from a hardware perspective. On previous genera- tions of systems, one or two GPS receivers were bolted somewhat awkwardly on long mast poles attached to the blade. Long cables – draped from the receivers to the body of the dozer – carried blade positioning information to the controllers in the cab. The new "mast-less" systems use low profi le receivers on the top of the cab and various combina- tions of sensors and inertial measurement units (IMUs) to orient the X-Y-Z position of the blade in space. The IMUs are basically gyroscopes mated to a controller or mini- computer. One immediate benefi t all these systems off er is that you no longer must attach to and remove the receivers or masts every day. The cost of these receivers made them attractive to thieves. Climbing up on the blade to remove the masts is also a safety concern. Not to mention they were somewhat precarious, since the masts were at risk of snapping off if the dozer was jolted hard enough. Finally, there was the possibility of the cables fraying or getting snagged in trees or other jobsite protrusions. All those concerns vanished with the new mast-free systems. Aside from the physical advantages of the new systems, the mast-less systems dial into sophisti- cated software in the control- lers that help you optimize the cut on each pass. You save fuel, track wear and engine and lube oil life by not overloading the machine to get to grade. Each of these systems (Caterpillar, Deere, Komatsu and Topcon) have diff erent component architecture and functionality. But what they all have in common is the ability to do GPS dozer operators faster and more effi ciently. So, we thought it would be useful to compare them, side by side. Here's how they work: CATERPILLAR Caterpillar's Grade with 3D system uses in-cylinder position sensors, which puts the sensor inside of the blade cylinders and out of harm's way, says Scott Hagemann, Cat market professional. Depending on the machine model and blade type, the system will have up to three in-cylinder position sensors: one each for lift, tilt and blade angle. The Cat Grade with 3D system takes you from fi rst pass to fi nal grade, says Hagemann, and is designed to move the most material the machine can move effi ciently. The operator starts moving material by lowering the blade. With Auto Carry turned on, as the blade load increases and the tracks start to slip, the blade will automatically rise to reduce the track slip and continue moving full blade loads. As the operator comes closer to grade, the system will lock on the design and drive the blade up and down automatically to stay on grade. The system needs to only be calibrated once at instal- lation. Along with the 3D system, Caterpillar includes the AccuGrade Ready Option and the wiring and brackets to add other technologies if your application or jobsite calls for them. The design can be transferred to the display by either a thumb drive, or wirelessly over cellular or Wi-Fi signals. Cat uses Trimble Business Center – HCE offi ce software to prepare 3D designs/ models to be loaded into their systems, Hagemann says. Trimble's software can also accept fi les created in several other civil engineering software systems, such as Bentley and AutoCAD. It can also import LandXML (.xml) fi les, which is an international standard fi le format that most common engineering software companies use for transferability between offi ce software systems. Typically, the machines use .svd and .svl fi le formats, although they can use a generic .dxf and a .ttm fi le as well.

Articles in this issue

Archives of this issue

view archives of IDA Universal - May/June 2017