IDA Universal

May/June 2017

Issue link: https://read.dmtmag.com/i/820377

Contents of this Issue

Navigation

Page 30 of 55

I DA U N I V E R S A L M ay -J u n e 2 0 1 7 31 The Cat Grade with 3D system is factory installed only and is available on models D3K2-D6K2, D6N, D6T, D8T and D9T. DEERE Deere's system combines technology from its dozer group with certain Topcon Positioning Systems compo- nents to accomplish its purpose, says Tammo Wagner, Deere manager, technology partner integration. There are two main control aspects to the system. One is a Topcon RTK (real-time kinematic) controller that synthesizes information from various sensors. Second is Deere proprietary software which enables the AutoSmartGrade function. The SmartGrade dozers take data from two IMUs, one on the body, one on the blade, rather than in-cylinder sensors, such as on the Cat system. The IMUs are housed inside small, sealed, low-profi le boxes to protect them from damage and dirt. If they should fail or get damaged, replacement is as simple as unbolting the box and bolting on a new one, Wagner says. The controllers are connected to a Deere- branded monitor in the cab and integrated with GPS antennae on the cab roof. The fi nal component is a radio antenna to which RTK correc- tion signals are transmitted from a base station on the jobsite. The IMUs determine where the blade is relative to the body of the machine. This positioning information is then paired with the machine information such as engine torque, percentage load and vehicle speed relative to track speed, which allows the machine to calculate track slip, Wagner says. By meshing positioning information and machine performance, the Smart Grade system determines if the machine is operating in the optimum productivity band or if some of the parameters related to the blade controls should be adjusted, says Wagner. For example, if the grade to be cut is too deep, as evidenced by track slippage or high torque, the Smart Grade controller will automati- cally raise the blade above the design grade, take a manageable cut and allow you to return for a second or third pass, until you reach the design grade. By not overloading the blade, you improve track life and fuel effi ciency. Deere SmartGrade customers typically load the 3D design fi les into the monitor using a thumb drive, but a telematics option is available, Wagner says. Because of the alliance Deere has with Topcon, the preferred software plan is the Topcon fi le format. Deere also has a strategic alliance with AGTEK, whose software allows you to transfer fi le formats back and forth between diff erent providers. Currently, the Smart Grade system is available on the Deere 700, 750 and 850 dozers, and more models are in the works, says Jena Holtberg-Benge, director, John Deere WorkSight. The system can also be retrofi tted with a fi eld kit to those same models of non-GPS equipped Deere dozers built since the Spring of 2016, she says. KOMATSU Komatsu's Intelligent Machine Control dozers make use of a cab-mounted GPS antenna, internal chassis-mounted enhanced inertial measuring units (IMU+), intelligent logic and stroke-sensing hydraulic cylinders, says Sebastian Witkowski, product marketing manager, Intelligent Machine Control, Komatsu America. The automatic machine control system can be used for fi nish grading, but also for heavy (rough) dozing as well, Witkowski says. Loading of the blade at the start of the cut is controlled by operator- selectable parameters. During the pass, if the blade load increases, the blade is automatically raised to control the load and minimize shoe slip to ensure effi cient dozing. When the blade approaches the target design surface, the blade will follow it for accurate fi nish grade. Design data can be trans- ferred to the machine via USB drive, or remote fi le transfer, which allows data to be sent directly to the machine from a web-enabled computer. Komatsu Intelligent Machine Control dozers make use of Topcon fi le format (.tp3). Most standardized formats can easily be converted to this format. Komatsu Intelligent Machine Control dozers are not designed to be retrofi tted, but factory installed and integrated, Witkowski adds. Komatsu America off ers a lineup of six intelligent machine control dozers, including the D39i-24, D51i-24, D61i-24, D65i-18, D85i-18 and D155AXi-8. TOPCON While Topcon does not make dozers, they have formed partnerships to provide mast-less compo- nents for diff erent OEM systems. The OEMs use Topcon components with their own proprietary systems to create diff erent systems for achieving the same goals. And Topcon has its own system, described below, which is either included on, or can be retrofi tted to a variety of machines. The complete Topcon 3D MC Max system uses dual IMU sensors – one on the body and another on the blade to increase on-grade performance and maximize speed and blade response, says Kris Maas, director of Each of these systems (Caterpillar, Deere, Komatsu and Topcon) have diff erent component architecture and functionality. But what they all have in common is the ability to do GPS dozer operators faster and more effi ciently. Continued on page 33

Articles in this issue

Archives of this issue

view archives of IDA Universal - May/June 2017